Fountain Set

Product No. 19731

The Fountain Set for water garden pumps includes 3 fountain heads including spray, bell and frothy patterns. Adjustable height allows for different pond depths and a flow control and diverter connects to 1/2 in., 3/4 in. and 1 in. ID tubing going to statuary, filters, or waterfalls. Adapters are included to fit all Tetra® Water Garden Pumps.

Sizes Available

This product comes in the following size: 1 ct

Product Reviews
Question & Answer

Could you please send me step by step guide for setting up my fountain set for the bubble?

Asked by: mime

We can send you the diagram of parts, and there is a general instruction sheet for our pumps that it attaches to. Basically, you use the diagram and simply connect the parts as it shows, starting from the bottom piece that connects to the top of the pump. I'll email what we have to you, but it is not a step by step instruction sheet. BREX

Answered by: BREX

Date published: 2018-11-30

How do you attach the 1” tubing adapter barb?  It says press but it’s the same size as the pipe on the diverter. 

Asked by: Pond pumpkin

The 1" tubing adapter is the side of the diverter with the screw on cap. Take the cap off, push the tubing on. It isn't an adapter. The two adapters it comes with are .5 and .75 inches ID. All of these connect to the side of the diverter with the cap and you just take the cap off to fit them onto the diverter. The press fit pieces are the pump adapters that screw into the top of the Water Garden Pumps. They have a smooth top that the diverter presses onto. There is also a piece that connects to the bottom of the frothy spray head. Unscrew it and take it out. It is a one inch press fit as well that you screw into the pump and can then attach tubing to the top of the pump, instead of off of diverter. Hope this helps! Call 1-800-526-0650 for more help. BREX

Answered by: BREX

Date published: 2018-08-28

I ordered this fountain, and it doesnt give you a diagram of how to assemble all the plastic pieces together. Wound up with extra pieces so dont think the fountain is working properly. Is thete a piece assembly diagram avail or cluld u send me one

Asked by: Edog

The diagram is on the back of the cardboard front of the package. And you should have some extra pieces as you can adjust the height for your pond, have three spray heads, total, and several adapters depending on if you want to also operate a spitter or UV light, etc. Be sure to turn the knob on the diverter so it is completely open to the fountain if you are not using a spitter as well. BREX

Answered by: BREX

Date published: 2018-08-11

I just bought a WGP Series Mag Drive Water Garden Pump with three heads for a fountain in my backyard fishpond. It came without tubing. Is there a Youtube video on how to assemble?

Asked by: Judybb46

The WGP does not come with heads for a fountain, but does come with adapters for attaching tubing to it, depending on what you wish to operate off of it. If you want a fountain, the fountain kit comes with a diverter that attaches to the top of the pump, and you don't use tubing to connect the two. This video may help you: http://www.tetra-fish.com/pond/learning-center/videos/chapter-6-equipment.aspx BREX

Answered by: BREX

Date published: 2018-06-12

Hi, I bought this kit last year and the the connections for the tubing cracked and fell apart. Can I purchase these connections?

Asked by: Steak

I have the same issue. the coupling do not seem to be very reliable. Mine lasted about a year as well unfortunately

Answered by: Abe1

Date published: 2018-05-29

Is there a replacement for the led lights?

Asked by: Smsw

Not at this time, so if yours are not working right, please call us at 1-800-526-0650 for warranty. BREX

Answered by: BREX

Date published: 2017-09-14

Love this fountain.  We have the LED Fountain Set.   Can the fountain spray be adjusted?

Asked by: Wondering Wanda

The height of it can be adjusted. As for the power of it, that would depend on the pump you attach it to as you would need to adjust the pump flow. BREX

Answered by: BREX

Date published: 2017-06-23

I purchased a pond pump fountain set and when I assemble the tubes and heads to form the bell pattern  the tubing leaks in various places on the assembly.  How do I fix this?  Should I use glues or hammer the pieces together?   

Asked by: Jerrym40

Neither, it shouldn't leak. Please email us a picture of how it is put together, and if possible, the leaking issue. Do you have the diverter opened all the way? BREX

Answered by: BREX

Date published: 2017-06-22

Fountain Set Questions - page 2

Sizes Available

Could you please send me step by step guide for setting up my fountain set for the bubble?

How do you attach the 1&rdquo; tubing adapter barb? &nbsp;It says press but it&rsquo;s the same size as the pipe on the diverter.&nbsp;

I ordered this fountain, and it doesnt give you a diagram of how to assemble all the plastic pieces together. Wound up with extra pieces so dont think the fountain is working properly. Is thete a piece assembly diagram avail or cluld u send me one

I just bought a WGP Series Mag Drive Water Garden Pump with three heads for a fountain in my backyard fishpond. It came without tubing. Is there a Youtube video on how to assemble?

Hi, I bought this kit last year and the the connections for the tubing cracked and fell apart. Can I purchase these connections?

Is there a replacement for the led lights?

Love this fountain. &nbsp;We have the LED Fountain Set. &nbsp; Can the fountain spray be adjusted?

I purchased a pond pump fountain set and when I assemble the tubes and heads to form the bell pattern &nbsp;the tubing leaks in various places on the assembly. &nbsp;How do I fix this? &nbsp;Should I use glues or hammer the pieces together? &nbsp;&nbsp;

How do you attach the 1” tubing adapter barb? It says press but it’s the same size as the pipe on the diverter.

Love this fountain. We have the LED Fountain Set. Can the fountain spray be adjusted?

I purchased a pond pump fountain set and when I assemble the tubes and heads to form the bell pattern the tubing leaks in various places on the assembly. How do I fix this? Should I use glues or hammer the pieces together?